{"product_id":"robojet-x-one-2-replacement-battery-144v-2600mah-li-ion","title":"RoboJet X-One 2 Replacement Battery 14.4V 2600mAh Li-ion","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eRoboJet X-One 2 Series — 14.4V Li-ion Replacement Battery (CMICR18650F8M-4S1P)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 14.4V, 2600mAh Li-ion battery pack for the RoboJet X-One 2 and X-One 2 Pro cordless stick vacuums. It replaces OEM part CMICR18650F8M-4S1P using a 4S1P cell configuration. When the original pack no longer holds a charge, this unit restores the vacuum to full working condition without replacing the entire machine.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eX-One 2 and X-One 2 Pro compatibility:\u003c\/strong\u003e\n    Both models run the same 14.4V motor rail and use the same battery connector and BMS handshake protocol. A single pack covers either variant — there is no electrical difference between the two at the battery interface.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through the X-One 2 motor startup sequence and sustained suction load. The BMS held voltage above the cutoff threshold across both carpet and hard floor draw profiles, and cell balance remained stable through full discharge cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging habit on the X-One 2:\u003c\/strong\u003e\n    Do not leave the vacuum sitting on the charging dock between uses. The X-One 2 dock does not terminate charge current cleanly at full capacity. Continuous dock contact causes trickle charge stress on Li-ion cells and accelerates capacity fade. Charge to full, then remove the unit from the dock.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when the motor is drawing more current than the BMS expects, usually because airflow is restricted. A partially blocked filter forces the motor to work harder, pulling amperage above the battery's rated discharge curve. The BMS responds by throttling output voltage before the indicator registers low — so the vacuum feels weak even though the pack still has charge. Clean or replace the filter first, then test suction. If the problem clears, the battery was not the cause.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cutting out mid-clean and then recovering after a few seconds\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a dead battery. When suction is sustained against heavy carpet pile or a partial blockage, current draw spikes past the BMS protection threshold and the pack shuts off briefly to protect the cells. The BMS resets automatically once current drops, which is why the motor comes back on its own. Clear any blockage in the nozzle or hose, confirm the filter is clean, and check that cell voltage reads at or above 14.0V on a fresh charge before ruling out a degraded pack.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43426487074906,"sku":"BWCS-RBX200VX-1","price":43.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43426487107674,"sku":"BWCS-RBX200VX-2","price":51.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43426487140442,"sku":"BWCS-RBX200VX-3","price":56.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-RBX200VX-1.webp?v=1779933440","url":"https:\/\/batteryweb.com\/products\/robojet-x-one-2-replacement-battery-144v-2600mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}