{"product_id":"robzone-duoro-xclean-replacement-battery-144v-2000mah-ni-mh","title":"RobZone Duoro XClean 14.4V Ni-MH Replacement Battery","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eRobZone Duoro XClean Series — 14.4V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 14.4V, 2000mAh Ni-MH replacement battery for the RobZone Duoro XClean cordless vacuum range. It fits the Duoro XClean, Duoro XClean 3.0, Duoro XClean Generace 2.0, Duoro XClean Generace 3.0, and at least five additional models in that lineup. Swap it in when the original cell no longer holds charge or the vacuum loses suction partway through a clean.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eDuoro XClean series compatibility:\u003c\/strong\u003e\n    These models share a common 14.4V battery rail and connector format across generations. The Generace 2.0 and 3.0 variants use the same cell configuration as the base XClean, so one battery format covers the full range without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge and discharge cycles on the XClean platform and monitored the BMS response under both open-floor and restricted-airflow loads. The protection circuit responded correctly to sustained overcurrent and did not trip under normal carpet passes.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging on the Duoro XClean:\u003c\/strong\u003e\n    Do not leave the vacuum sitting on the charging dock continuously between uses. Ni-MH cells in cordless vacuums develop capacity fade significantly faster under constant trickle charge. Charge to full, then remove from the dock.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low on the Duoro XClean\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells show voltage sag under load before the resting voltage reflects any real capacity loss. On the Duoro XClean, a partially blocked filter forces the motor to draw more current than rated, which accelerates that sag. The battery indicator reads the resting voltage, not the loaded voltage — so suction weakens well before the light triggers. Clean or replace the filter first; if suction restores immediately, the battery is not the cause.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cutting out mid-clean and recovering after a short pause\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a flat battery. When airflow is restricted — blocked filter, jammed brush roll, or clogged inlet — the motor draws sustained current above the BMS threshold and the protection circuit cuts power. A short pause lets the BMS reset and the vacuum restarts. Clear the blockage completely, then check that the filter is seated correctly. If trips continue on a clean filter with a new battery, measure terminal voltage at load — it should hold above 12V under normal suction conditions.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43428063412314,"sku":"BWCS-ECR120VX-1","price":57.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43428063445082,"sku":"BWCS-ECR120VX-2","price":66.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43428063477850,"sku":"BWCS-ECR120VX-3","price":73.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-ECR120VX-1.webp?v=1779934014","url":"https:\/\/batteryweb.com\/products\/robzone-duoro-xclean-replacement-battery-144v-2000mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}