{"product_id":"samsung-it100-replacement-battery-37v-1050mah-li-ion","title":"Samsung SLB-10A IT100 Replacement Battery 3.7V 1050mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eSamsung IT100 \/ SL620 \/ PL60 — 3.7V Li-ion Replacement Battery (SLB-10A)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.7V, 1050mAh Li-ion cell built to the SLB-10A spec. It fits the Samsung IT100, SL620, PL60, ES55, and over 52 additional Samsung compact camera models. The cell slots into the same battery compartment as the OEM unit and connects via the same four-contact interface.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eIT100 \/ SL620 \/ PL60 \/ ES55 platform:\u003c\/strong\u003e\n    These models share the same compact body format, battery bay dimensions, and four-contact BMS interface. The SLB-10A footprint — 43.30 × 31.30 × 7.10mm — fits all of them without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through a full charge and discharge cycle on an IT100 body. The BMS handshake completed on first insert, the battery indicator populated correctly, and the cell held voltage through sustained continuous shooting without dropping to the low-battery cutoff prematurely.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-cycle acceptance on the IT100:\u003c\/strong\u003e\n    Some Samsung compact bodies map the battery-remaining display against a charge cycle completed inside the camera body itself. Charge this cell in-camera or via an OEM-compatible external charger before your first shoot to let the BMS calibrate the indicator correctly.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eFlash recycling current draw and cell voltage at end of charge\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe IT100's built-in flash capacitor pulls a short high-current burst each time it recharges between shots. Early in a charge cycle this is not an issue, but as the cell discharges below roughly 3.5V, that recharge current causes a momentary voltage sag. The camera body reads the sag and may flag a low-battery warning even when capacity remains. This is a BMS threshold response, not a faulty cell. Slowing your shooting rate slightly at the tail end of a session gives the capacitor time to recharge without triggering the cutoff.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBattery percentage jumping erratically on the IT100 display\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eSamsung's compact camera firmware maps battery percentage against a discharge curve calibrated to the original OEM cell. A replacement cell with a slightly different discharge curve can cause the indicator to jump — showing 60%, then dropping to 20% within a few frames. The cell is not defective; the BMS voltage-to-percentage mapping just hasn't yet learned the new cell's curve. Run two full charge and discharge cycles in the camera body and the indicator typically stabilises. After the second cycle, the reading should track within a few percent of actual remaining capacity.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43333873303642,"sku":"BWCS-SLB10A-1","price":23.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43333873336410,"sku":"BWCS-SLB10A-2","price":26.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43333873369178,"sku":"BWCS-SLB10A-3","price":29.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-SLB10A-1.webp?v=1778213403","url":"https:\/\/batteryweb.com\/products\/samsung-it100-replacement-battery-37v-1050mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}