{"product_id":"sanyo-ges-pcf07-replacement-battery-24v-1200mah-ni-mh","title":"Sanyo GES-PCF07 Cordless Phone Replacement Battery 2.4V 1200mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eSanyo GES-PCF07 — 2.4V Ni-MH Replacement Battery (GES-PCF07)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 2.4V, 1200mAh Ni-MH battery pack for Sanyo cordless phone handsets that specify the GES-PCF07. It replaces the original pack when the handset can no longer hold enough charge for normal use. Dimensions are 50.36 x 28.11 x 14.33mm — confirm these match your existing pack before ordering.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eGES-PCF07 handset compatibility:\u003c\/strong\u003e\n    Sanyo cordless phones using this part number share the same 2.4V two-cell Ni-MH configuration, connector orientation, and physical footprint. The base station charges to a fixed voltage ceiling set for this chemistry — swapping in a mismatched voltage pack trips the charging circuit.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through charge and discharge on the bench. The BMS held stable at 2.4V nominal, and the cells accepted a full charge without thermal event or early cutoff across repeated cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-install charge for Ni-MH cordless packs:\u003c\/strong\u003e\n    After fitting this battery, seat the handset in the base and leave it for a full 16 hours before use. Ni-MH cells shipped in partial-discharge state will not reach rated capacity on a standard short charge — the slow first cycle is what brings the cells up to full capacity.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBase station charge light not activating on a new Ni-MH pack\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eCordless phone bases detect a new battery by looking for a voltage above their acceptance threshold — typically around 2.0V for a 2.4V Ni-MH pack. Batteries that have self-discharged during storage can arrive below this threshold, causing the base to show no charge activity or an error light. The fix is to briefly short-cycle the handset: power it on for 30 seconds, then return it to the base. This small discharge pulse drops internal resistance enough for the charger to detect and engage the pack. Once the charge light activates, leave the handset docked for the full 16-hour initial charge.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eTalk time noticeably shorter than the original battery for the first few uses\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells do not deliver rated capacity on the first cycle — they need three to five full charge-discharge cycles to reach the 1200mAh figure. On the first use, actual capacity can read 20–30% lower than rated, which is normal cell behaviour, not a fault. Run the handset until the low-battery indicator activates, return it to the base for a full charge, and repeat. By cycle five, voltage under RF transmit load should stabilise above 2.2V and talk time will reflect the rated capacity.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43339995742298,"sku":"BWCS-BPT50CL-1","price":12.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43339995775066,"sku":"BWCS-BPT50CL-2","price":13.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43339995807834,"sku":"BWCS-BPT50CL-3","price":14.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BPT50CL-1.webp?v=1778367024","url":"https:\/\/batteryweb.com\/products\/sanyo-ges-pcf07-replacement-battery-24v-1200mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}