{"product_id":"scantronic-i-on-compact-replacement-battery-72v-2000mah-ni-mh","title":"Scantronic i-on Compact 7.2V Replacement Battery BAT01","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eScantronic i-on Compact — 7.2V Ni-MH Replacement Battery (BAT01)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 7.2V, 2000mAh Ni-MH replacement battery for the Scantronic i-on Compact alarm panel. It slots into the backup power compartment and keeps the panel running during a mains power failure. The OEM part reference is BAT01.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003ei-on Compact panel fit:\u003c\/strong\u003e\n    The i-on Compact uses a dedicated 7.2V Ni-MH cell pack with a specific connector and physical footprint. This battery matches those dimensions (86.50 × 51.80 × 14.60mm), the voltage rail the panel charges at, and the BMS handshake the control board expects before accepting the cell as valid.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell against the i-on Compact charge circuit and confirmed the panel accepted the battery, moved through charge stages correctly, and cleared its low-battery fault flag within the expected conditioning window.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-install stabilisation:\u003c\/strong\u003e\n    Do not run a zone or siren test immediately after fitting this battery. Allow 24–48 hours on float charge first. The panel samples backup voltage before triggering diagnostics — testing too early will cause a false low-battery report even with a healthy new cell.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eAlarm panel showing low battery hours after installing new cell\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe i-on Compact does not report battery status from a single voltage snapshot at installation. It monitors the cell over a charge cycle before updating the battery status flag. A freshly installed Ni-MH cell at partial charge will read below the panel's acceptance threshold until it completes a full float cycle. Leave the panel on mains power for 24–48 hours — the low-battery indicator should clear once the cell holds above 7.0V under light load.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eAlarm losing programming during a power cut after battery replacement\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eIf the panel loses its zone settings or user codes during a mains outage shortly after a battery swap, the new cell had not yet been accepted by the backup circuit. The i-on Compact conditions the replacement cell over roughly 48 hours before it is treated as a live backup source. Until conditioning completes, a mains drop leaves the panel without sufficient voltage to hold RAM. Restore mains power, allow 48 hours of uninterrupted charging, then confirm the panel holds programming through a brief mains-off test.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43309819789402,"sku":"BWCS-SAT100BT-1","price":48.99,"currency_code":"USD","in_stock":false},{"title":"Warranty 2 Year","offer_id":43309819822170,"sku":"BWCS-SAT100BT-2","price":57.99,"currency_code":"USD","in_stock":false},{"title":"Warranty 3 Year","offer_id":43309819854938,"sku":"BWCS-SAT100BT-3","price":63.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-SAT100BT-1.webp?v=1777868450","url":"https:\/\/batteryweb.com\/products\/scantronic-i-on-compact-replacement-battery-72v-2000mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}