{"product_id":"schiller-br-102-replacement-battery-48v-500mah-ni-mh","title":"Schiller BR-102 Defibrillator Compatible Battery 4.8V 500mAh 110074","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eSchiller BR-102 — 4.8V Ni-MH Replacement Battery (110074)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 4.8V 500mAh Ni-MH battery replaces the internal power cell in the Schiller BR-102 blood pressure recording unit, also listed under the ODAM and Bruker Enregistreur de Pression Artérielle BR-102 designations. It matches OEM part numbers 110074 and 9712566009. Voltage and capacity are exact to spec — no substitutions.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eBR-102 platform fit:\u003c\/strong\u003e\n    The BR-102, Blutdruckmessgerat BR102, and ODAM\/Bruker-badged variants share the same internal cell footprint and connector pinout. The 66.40 × 33.20 × 13.00mm form factor seats directly into each unit without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through charge and discharge on the bench, confirmed BMS handshake at startup, and verified the protection circuit holds cutoff at the correct low-voltage threshold. No false fault codes triggered during our test sequence.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-installation self-test:\u003c\/strong\u003e\n    After fitting the new cell, allow the BR-102 to complete its full power-on self-test without interruption. The device BMS runs a verification routine at startup — cutting power during this sequence generates a persistent battery fault flag that will not clear until the next complete reboot cycle.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBR-102 Self-Test Failure After Battery Swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe BR-102 runs an internal BMS learn cycle when a new cell is installed. A freshly fitted Ni-MH cell that has not completed one full charge-discharge cycle may not meet the device's internal voltage profile check, causing a self-test failure flag. This is not a faulty battery — it is the BMS applying OEM chemistry thresholds before the cell has stabilised. Run one complete charge cycle from flat to full, then allow the device to complete its startup sequence before clinical use.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBR-102 Will Not Power On After the Cell Has Been in Storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells self-discharge in storage, and a deeply discharged cell can fall below the BMS recovery threshold — the device sees the voltage as too low to initiate boot and refuses to power on. Connect the unit to its charger and leave it for a minimum of 30 minutes before attempting to power on. Most BMS circuits on this class of device begin recovery charging at voltages above 3.6V; if the cell has dropped below that point, recovery charging may take longer. Once the cell climbs above the recovery threshold, the device will boot normally.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381422587994,"sku":"BWCS-SHR102MD-1","price":30.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381422620762,"sku":"BWCS-SHR102MD-2","price":34.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381422653530,"sku":"BWCS-SHR102MD-3","price":37.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-SHR102MD-1.webp?v=1778900681","url":"https:\/\/batteryweb.com\/products\/schiller-br-102-replacement-battery-48v-500mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}