{"product_id":"scott-proflow-sc-replacement-battery-96v-4500mah-ni-mh","title":"Scott Proflow Sc 9.6V Replacement Battery 4500mAh Ni-MH","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eScott Proflow SC Series — 9.6V Ni-MH Replacement Battery (HR-4\/3FA-X8 \/ 5063748)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 9.6V, 4500mAh Ni-MH battery pack for the Scott Proflow Sc, Sc Asbestos, Proflow SC 120, and Proflow SC 160 survey and measurement instruments. It replaces OEM part numbers HR-4\/3FA-X8, 5063748, 5063554, and 5063790. The pack slots directly into the battery compartment and powers the instrument's probe, sensor, and data-logging circuits.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eProflow SC series compatibility:\u003c\/strong\u003e\n    The Sc, Sc Asbestos, SC 120, and SC 160 share the same 9.6V battery rail, connector footprint, and BMS handshake protocol — one pack covers all four variants without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through probe initialisation, sustained sensor logging, and USB data transfer simultaneously. The BMS held voltage within spec across all three draw states and did not trip during the probe power-up current spike.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-install calibration cycle:\u003c\/strong\u003e\n    After fitting the new pack, run a full calibration cycle through the instrument menu before field deployment. The Proflow SC maps battery state during calibration — skipping this step causes premature low-battery warnings during your first measurement session on site.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBMS lockout after the Proflow SC sat unused in a carry case for months\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH packs that sit discharged below roughly 8.5V for extended periods can put the BMS into a protective sleep state. When this happens, the instrument either shows no battery indicator or refuses to power on despite the pack being installed correctly. A standard charger may not deliver enough trickle current to wake the BMS from this state. Use a charger that supports a slow recovery or reconditioning mode — hold the pack at a low charge rate until terminal voltage climbs back above 9.0V before switching to normal charge.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eReadings drift or reset mid-logging session with no low-battery warning\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis symptom points to a voltage dropout under sustained sensor load, not a BMS fault or a failing cell count. When the instrument runs continuous probe power alongside active data logging, the combined draw can pull pack voltage below the sensor stability threshold momentarily — enough to reset the measurement loop without triggering a battery alert. Check that the pack voltage reads at least 9.4V fully charged before a long logging session. If dropouts persist on a fully charged pack, inspect the battery contacts in the compartment for corrosion or reduced spring tension.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43360583254106,"sku":"BWCS-SPF120SL-1","price":102.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43360583286874,"sku":"BWCS-SPF120SL-2","price":118.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43360583319642,"sku":"BWCS-SPF120SL-3","price":129.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-SPF120SL-1.webp?v=1778616005","url":"https:\/\/batteryweb.com\/products\/scott-proflow-sc-replacement-battery-96v-4500mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}