{"product_id":"shark-wv200uk-replacement-battery-108v-2000mah-li-ion","title":"Shark XFBT200 Replacement Battery 10.8V 2000mAh Li-ion","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eShark WV200UK — 10.8V Li-ion Replacement Battery (XFBT200)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 10.8V, 2000mAh Li-ion replacement battery for the Shark WV200UK handheld cordless vacuum. It also fits the WV200, WV201, and WV205 models. Same voltage, same connector, same BMS handshake as the original XFBT200.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eWV200 series compatibility:\u003c\/strong\u003e\n    The WV200, WV201, and WV205 share the same 10.8V battery platform and connector housing. The BMS in each model expects the same cell voltage range and charge termination signal — a mismatched cell pack will either refuse to charge or cut out under motor load.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through full charge and discharge cycles on the WV200 platform. The BMS held cutoff correctly at low-cell threshold, and charge termination triggered cleanly without the charger locking out — common with aftermarket cells that spoof the handshake incorrectly.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging on the WV200 series:\u003c\/strong\u003e\n    Do not leave the vacuum sitting on the charging dock permanently. Continuous trickle charging accelerates capacity fade on Li-ion cells in handheld vacuums faster than regular charge-and-remove cycles. Charge to full, then pull it off the dock.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator shows low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe WV200's suction motor draws significantly more current when the filter is partially blocked. A restricted airflow path forces the motor to work harder, pulling the cell voltage down faster than the indicator circuit registers. The battery indicator reads state-of-charge from resting voltage, not under-load voltage — so it can show two bars while the motor is already starving. Clean or replace the filter first, then retest suction under load.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cuts out mid-use then recovers after a short pause\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a dying battery. When the vacuum picks up a blockage or runs against dense carpet fibres, the motor draws a current spike that the BMS reads as a fault condition and shuts the pack down. After 10–30 seconds, the BMS resets and power returns. Clear any blockage from the nozzle and filter path, then test again — if the cutout stops, the cell is fine. If it persists on a clear filter, check that the replacement pack's BMS overcurrent threshold matches the OEM spec at 10.8V nominal.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43428029268058,"sku":"BWCS-EWV200VX-1","price":53.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43428029300826,"sku":"BWCS-EWV200VX-2","price":62.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43428029333594,"sku":"BWCS-EWV200VX-3","price":69.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-EWV200VX-1.webp?v=1779933901","url":"https:\/\/batteryweb.com\/products\/shark-wv200uk-replacement-battery-108v-2000mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}