{"product_id":"sharp-bt70-replacement-battery-6v-4200mah-ni-mh","title":"Sharp BT70 Replacement Battery 6V 4200mAh Ni-MH","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eSharp BT70 \/ BT77 \/ BT80 \/ FZ168 — 6V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 6V, 4200mAh (25.2Wh) Ni-MH replacement battery for Sharp camcorders including the BT70, BT77, BT80, and FZ168 series. It fits the same battery compartment as the original Sharp cell and runs off the same voltage rail. Use it when the original cell no longer holds a charge across a full recording session.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eBT70 \/ BT77 \/ BT80 \/ FZ168 platform fit:\u003c\/strong\u003e\n    These models share a 6V Ni-MH power architecture with the same physical connector and cell format. The BMS in each body communicates charge state through the same contact arrangement, so one cell type covers the whole group.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge and discharge cycles on a Sharp camcorder body. The BMS accepted the cell without error flags, and charge termination triggered correctly at full capacity without overrun.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-cycle conditioning on Ni-MH:\u003c\/strong\u003e\n    Ni-MH cells shipped in a partially discharged state benefit from one full charge-discharge cycle before regular use. Run the battery down to automatic shutoff, then charge fully in the camcorder body or OEM charger. This lets the BMS calibrate its charge-remaining estimate accurately from the first session.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the Sharp BT70 reports low battery earlier than expected on a new cell\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eSharp camcorder BMS firmware maps battery percentage against a voltage-discharge curve built around the original aged cell. A fresh 4200mAh Ni-MH cell has a flatter discharge curve than a worn one, so the indicator can read low while the cell still has meaningful capacity remaining. This mismatch corrects itself after two or three full charge-discharge cycles once the BMS recalibrates its internal reference. If the indicator remains erratic after three cycles, verify the contacts on the battery door are clean and making consistent contact.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCamcorder cuts to standby mid-recording even with a charged battery\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eSustained video recording on the BT70 series draws current from the sensor, processor, and image stabilisation simultaneously. If the cell voltage dips under load — even briefly — the body interprets it as a depleted battery and halts recording. On Ni-MH cells, this voltage sag is more pronounced when the cell is cold or has not yet completed a conditioning cycle. Warm the camera to room temperature before a long recording run and confirm the cell has completed at least one full cycle; a rested, fully charged cell should hold above 5.4V under normal recording load.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43333907447898,"sku":"BWCS-NP66-1","price":50.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43333907480666,"sku":"BWCS-NP66-2","price":58.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43333907513434,"sku":"BWCS-NP66-3","price":64.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-NP66_1.webp?v=1778213590","url":"https:\/\/batteryweb.com\/products\/sharp-bt70-replacement-battery-6v-4200mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}