{"product_id":"sonel-lkz-1500-cable-detector-replacement-battery-6v-2000mah-ni-mh","title":"Sonel LKZ-1500 Cable Detector Replacement Battery 6V 2000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eSonel LKZ-1500 Cable Detector — 6V Ni-MH Replacement Battery (WAAKU23)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 6V 2000mAh Ni-MH battery for the Sonel LKZ-1500 underground cable locator. It replaces OEM parts WAAKU23, AKU-23, and AA2006BT. The LKZ-1500 uses this pack to power its signal receiver and display during buried utility detection work.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eLKZ-1500 locator compatibility:\u003c\/strong\u003e\n    Both the cable detector and locator variants of the LKZ-1500 run the same 6V bus with identical connector housings and BMS handshake requirements — this single pack covers both configurations without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through the LKZ-1500's signal-processing load profile. The BMS held voltage above the instrument's 5.4V cutoff threshold under sustained receiver operation, and the protection circuit responded correctly to the brief current spike at detector power-up.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eField deployment preparation:\u003c\/strong\u003e\n    After fitting this pack, run a full calibration cycle through the LKZ-1500's instrument menu before heading to site. The detector maps battery state during calibration — skipping this step causes premature low-battery warnings during your first active scan session.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBMS lockout after the LKZ-1500 sat unused in a carry case\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells self-discharge at roughly 1–2% per day. A pack stored in a closed case for several months can drop below 4.8V total — the threshold where the BMS latches into protection mode and refuses to accept a charge. The charger shows no activity, and the detector stays dark. To recover the pack, apply a gentle reconditioning charge at 50–100mA until cell voltage climbs back above 5.0V, then resume normal charging.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eLKZ-1500 display resets or readings drop out mid-scan\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when the signal processor triggers a higher-draw sampling burst and the pack can't maintain voltage under that transient load. On Ni-MH cells with partial charge, internal resistance rises enough to cause a brief voltage sag below the detector's logic reset point — the display blanks or the reading clears. The fault is not a firmware issue. Charge the pack fully and confirm resting voltage reads at or above 6.0V before starting a logging session.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43360517816410,"sku":"BWCS-LKZ150SL-1","price":34.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43360517849178,"sku":"BWCS-LKZ150SL-2","price":39.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43360517881946,"sku":"BWCS-LKZ150SL-3","price":43.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-LKZ150SL-1.webp?v=1778615946","url":"https:\/\/batteryweb.com\/products\/sonel-lkz-1500-cable-detector-replacement-battery-6v-2000mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}