{"product_id":"sonos-cb200-replacement-battery-37v-1850mah-li-ion","title":"Sonos CB200 Remote Compatible Battery 3.7V 1850mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eSonos CB200 \/ CR200 Controller — 3.7V Li-ion Replacement Battery (URC-CB200)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.7V 1850mAh Li-ion battery for the Sonos CB200 and CR200 wireless remote controls. It fits the CB200, CB200WR1, CR200, and Controller 200 series handsets used to manage Sonos speaker systems. When the original cell dies, this replacement restores full control of playback, volume, and system settings.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eCB200 and CR200 platform fit:\u003c\/strong\u003e\n    These two remote lines share the same internal cell format, connector orientation, and BMS handshake protocol — which is why a single replacement battery covers both. Voltage tolerance across the range is 3.7V nominal with the same charge curve.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell in a CB200 unit and confirmed the BMS accepted the charge cycle without fault flags. The remote powered on immediately after install and the IR output registered at full LED drive current.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eSingle-cell remote swap rule:\u003c\/strong\u003e\n    The CB200 runs on one Li-ion cell — but if your unit has a secondary backup cell or any companion device sharing a charge dock, replace them at the same time. A mismatched age gap between cells causes the newer cell to carry the full load and degrade faster.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the CB200 remote stops responding mid-session even with charge remaining\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eLi-ion cells in low-draw remotes degrade through shallow-cycle fatigue — the cell is rarely fully discharged, so capacity loss builds quietly over hundreds of partial cycles. The BMS in the CB200 cuts IR LED power before the battery hits its true floor voltage, which means the remote stops triggering commands while the charge indicator still reads non-zero. The battery isn't flat — it's below the minimum threshold the IR circuit needs to fire reliably. Replacing the cell resets that threshold immediately.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCB200 showing no response at all after battery replacement\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe most common cause after a fresh install is reversed polarity — the Li-ion cell in the CB200 is easy to seat backwards because the connector can accept both orientations physically. A reversed cell delivers no voltage to the logic board, so the remote shows zero signs of life. Open the compartment and confirm the positive terminal on the cell aligns with the marked positive contact on the PCB. Correct orientation and the remote will power on without any reset step required.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43416109908058,"sku":"BWCS-CB200RC-1","price":24.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43416109940826,"sku":"BWCS-CB200RC-2","price":27.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43416109973594,"sku":"BWCS-CB200RC-3","price":30.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-CB200RC-1.webp?v=1779760313","url":"https:\/\/batteryweb.com\/products\/sonos-cb200-replacement-battery-37v-1850mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}