{"product_id":"sony-prs-300-replacement-battery-37v-680mah-li-polymer","title":"Sony PRS-300 Replacement Battery LIS1382(S) 3.7V 680mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eSony PRS-300 Series — 3.7V Li-Polymer Replacement Battery (LIS1382(S))\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.7V, 680mAh lithium-polymer replacement battery for the Sony PRS-300 e-reader series. It fits the PRS-300, PRS-300SC, PRS-300RC, and PRS-300BC. It replaces OEM part LIS1382(S) and cross-references 1-756-769-31, 9702A50844, and 9924A60515.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003ePRS-300 series fit:\u003c\/strong\u003e\n    The SC, RC, and BC variants of the PRS-300 share the same battery bay dimensions, voltage rail, and connector pinout as the base model. One cell covers all four variants without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through the PRS-300's charge circuit and confirmed the BMS accepted charge without flagging an incompatible cell. Charge termination and cutoff voltage behaved as expected at the device's 4.2V ceiling.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-swap charge cycle:\u003c\/strong\u003e\n    After installing this cell, charge via USB before powering on. The PRS-300 firmware reads battery state-of-charge at boot. If the cell voltage is below the boot threshold from storage, the device will not initialise — connect USB first and allow at least a partial charge before pressing the power button.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the PRS-300 shows incorrect battery percentage after a cell swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe PRS-300 stores a charge profile in firmware tied to the previous cell's discharge curve. After swapping to a new cell, the displayed percentage will often read inaccurately for the first few cycles. This is not a fault with the replacement cell — it is the firmware recalibrating its internal model. Run two or three full charge-to-discharge cycles and the percentage display will stabilise. No hardware reset is required.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003ePRS-300 not powering on after battery replacement\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eReplacement cells ship at partial storage voltage, typically around 3.6–3.8V. The PRS-300 requires a minimum boot voltage closer to 3.7V to initialise the e-ink controller — cells at the low end of storage voltage will not clear that threshold. Connect the device to a USB power source immediately after installation and wait at least 10 minutes before attempting to power on. If the charge LED activates, the cell is seated correctly and the device will boot once voltage climbs above the boot threshold.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43360267599962,"sku":"BWCS-PRD300SL-1","price":23.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43360267632730,"sku":"BWCS-PRD300SL-2","price":26.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43360267665498,"sku":"BWCS-PRD300SL-3","price":29.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-PRD300SL-1.webp?v=1778611066","url":"https:\/\/batteryweb.com\/products\/sony-prs-300-replacement-battery-37v-680mah-li-polymer","provider":"BatteryWeb","version":"1.0","type":"link"}