{"product_id":"spinwave-wet-and-dry-robotic-vacuum-replacement-battery-148v-2600mah-li-ion","title":"SpinWave Wet Dry Robotic Vacuum Compatible Battery 14.8V 2600mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eSpinWave Wet and Dry Robotic Vacuum (5345 \/ 1618526 \/ 1625424) — 14.8V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 14.8V, 2600mAh lithium-ion battery for the SpinWave Wet and Dry Robotic Vacuum. It fits models 5345, 1618526, and 1625424. When the original cell degrades and the robot can no longer complete a full cleaning cycle, this replacement restores normal operation.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eModel compatibility — 5345, 1618526, 1625424:\u003c\/strong\u003e\n    These units share the same 14.8V battery bay, connector pinout, and BMS handshake protocol. Swapping between them is a direct physical and electrical match — no adapter or firmware change needed.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge and discharge cycles on the SpinWave platform. The BMS communicated correctly with the robot's charge controller, and overcurrent cutoff triggered at expected thresholds during simulated motor load.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging practice for this robot:\u003c\/strong\u003e\n    Do not leave the SpinWave sitting on its dock indefinitely between uses. Continuous trickle charging on a docked robot compresses cell capacity faster than periodic charge cycles. Charge fully, then lift the unit off the dock until the next scheduled clean.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe SpinWave's motor controller pulls harder when suction is restricted — a partially blocked filter or brush roll makes the motor draw above its rated current. The BMS reads this as a low-voltage event and throttles output before the charge indicator reflects actual capacity. The result is reduced suction while the display still shows mid-charge. Clear the filter and brush roll first; if suction normalises, the battery is fine and the cell was never the issue.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cuts out mid-cycle then recovers on its own\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a dead battery. When the brush roll catches debris or the filter is heavily loaded, current draw spikes past the BMS threshold and the battery disconnects to protect the cells. The robot pauses, the BMS resets internally, and power returns — typically within a few seconds. Check filter restriction first. If the cutout persists on a clean filter, measure resting pack voltage: a healthy cell at partial charge should read above 14.0V.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43428013310042,"sku":"BWCS-MVS500VX-1","price":37.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43428013342810,"sku":"BWCS-MVS500VX-2","price":43.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43428013375578,"sku":"BWCS-MVS500VX-3","price":48.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-MVS500VX-1.webp?v=1779933850","url":"https:\/\/batteryweb.com\/products\/spinwave-wet-and-dry-robotic-vacuum-replacement-battery-148v-2600mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}