{"product_id":"thermo-scientific-s1-pipet-filler-replacement-battery-37v-2800mah-li-ion","title":"Thermo Scientific S1 Pipet Filler 3.7V 2800mAh Replacement Battery","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eThermo Scientific S1 Pipet Filler — 3.7V Li-ion Replacement Battery (Y\/W0823)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 3.7V, 2800mAh Li-ion cell replaces the OEM battery in the Thermo Scientific S1 Pipet Filler. The S1 is an electronic pipette dispensing tool used in laboratory and clinical environments for precise, repeatable liquid handling. Voltage and capacity match the original specification exactly — 3.7V nominal, 2800mAh (10.36Wh).\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eS1 Pipet Filler platform fit:\u003c\/strong\u003e\n    The S1 uses a single-cell Li-ion pack at 3.7V with a BMS that verifies cell chemistry on power-up. This replacement shares the same voltage rail, connector pinout, and pack geometry (66.00 × 20.32 × 18.36mm), so the BMS handshake completes without fault codes.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through charge and full-load aspiration sequences. The BMS accepted the cell, current draw stayed within the motor driver's rated envelope, and cutoff thresholds triggered correctly at low voltage.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePower-on self-test protocol:\u003c\/strong\u003e\n    After fitting this battery, let the S1 complete its full startup self-test without interrupting power. The BMS runs a verification cycle at boot — cutting power mid-sequence flags a false battery fault that persists until the next clean reboot.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharge indicator stuck below 100% on the first charge cycle\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe S1's charge IC applies a conservative current limit when it detects a new or unrecognised cell. This is a deliberate protection step — not a fault. The cell is still charging; the indicator just won't advance to full until the IC completes its first taper phase. Run one complete uninterrupted charge from flat to full. After that first cycle, the charge IC recalibrates its end-of-charge voltage target and the indicator reads normally.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eS1 shutting off unexpectedly during aspiration in the first week of use\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNew Li-ion cells carry a slightly elevated internal resistance before the first several charge-discharge cycles break in the electrode structure. During aspiration, the S1 motor draws a short but sharp current spike. On a new cell, that spike causes a momentary voltage sag that can dip below the BMS undervoltage cutoff — triggering a shutdown even at 60–70% indicated charge. This is not a defective battery. Run three to five full charge-discharge cycles in normal use and the internal resistance drops enough that the sag stays above the 3.0V cutoff threshold.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381502574682,"sku":"BWCS-TSN833MD-1","price":30.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381502607450,"sku":"BWCS-TSN833MD-2","price":35.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381502640218,"sku":"BWCS-TSN833MD-3","price":38.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-TSN833MD-1.webp?v=1778901340","url":"https:\/\/batteryweb.com\/products\/thermo-scientific-s1-pipet-filler-replacement-battery-37v-2800mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}