{"product_id":"toshiba-dect-2060-replacement-battery-24v-700mah-ni-mh","title":"Toshiba DECT 2060 Replacement Battery 2.4V 700mAh Ni-MH","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eToshiba DECT 2060 \/ DECT 2080 — 2.4V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 2.4V, 700mAh Ni-MH replacement battery for the Toshiba DECT 2060 and DECT 2080 cordless handsets. It slots into the battery compartment on the back of the handset and restores charging and standby function. No OEM part number is published for this cell — the fit is confirmed by physical dimensions (46.46 x 23.00 x 10.61mm) and voltage match.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eDECT 2060 and DECT 2080 compatibility:\u003c\/strong\u003e\n    Both handsets share the same battery bay dimensions and 2.4V charging rail from the base station. A single cell pack at this voltage satisfies the base charge termination logic on both models without triggering a fault condition.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through charge and discharge on a 2.4V NiMH test rig. The BMS in the base accepted the pack without error, and voltage at full charge measured within the expected 2.8–2.9V range for a two-cell NiMH configuration.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst charge after installation:\u003c\/strong\u003e\n    Place the handset in the base immediately after installing this battery and leave it for a full 16 hours before taking it off the cradle. NiMH cells shipped in storage state need a slow initial charge to reach rated capacity — a short first charge will leave you with noticeably reduced talk time for the first several cycles.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eRange dropping after a battery swap on the DECT 2060\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eDECT handsets regulate transmit power, but the RF output still depends on the battery holding voltage under load. A new NiMH pack that hasn't been fully conditioned will sag faster under the current draw of the radio transmitter. That sag causes the handset to drop its effective range before the low-battery indicator even appears. Run three to five full charge and discharge cycles to condition the cells — range typically stabilises by the third cycle.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBase station shows no charge light after installing the new battery\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNiMH cells sitting in storage can arrive at a voltage low enough that the base station's charge circuit doesn't recognise the pack as a valid battery. The base expects to see a minimum voltage before it activates the charge current. If the charge indicator stays off after seating the handset, remove it, wait ten seconds, and reseat it firmly — this resets the base's detection cycle. If the light still doesn't come on, check that the handset contacts are clean and making full contact with the cradle pins; oxidation on either surface breaks the circuit the base uses to detect the pack.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43340046827610,"sku":"BWCS-UT2060CL-1","price":20.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43340046860378,"sku":"BWCS-UT2060CL-2","price":23.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43340046893146,"sku":"BWCS-UT2060CL-3","price":25.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-UT2060CL-1.webp?v=1778367047","url":"https:\/\/batteryweb.com\/products\/toshiba-dect-2060-replacement-battery-24v-700mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}