{"product_id":"trismed-vitapia7000k-type7012k-replacement-battery-74v-13500mah-li-ion","title":"Trismed VITAPIA7000K Compatible Battery 7.4V 13500mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eTrismed VITAPIA7000K (Type7012K) — 7.4V Li-ion Replacement Battery (855183P)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 7.4V, 13500mAh Li-ion battery replaces OEM part 855183P in the Trismed VITAPIA7000K patient monitoring system. It provides backup power to the Type7012K monitor during mains interruptions, keeping vital signs data uninterrupted at the bedside. Voltage, connector, and BMS communication match the original specification.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eVITAPIA7000K (Type7012K) fitment:\u003c\/strong\u003e\n    The Type7012K platform uses a single-cell-pack design with a specific BMS handshake tied to the 855183P part number. This replacement carries the same 7.4V nominal rail and BMS protocol, so the monitor's charge controller recognises the pack without a compatibility fault.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through the VITAPIA7000K charge-discharge sequence and verified that the BMS reported state-of-charge correctly at 25%, 50%, 75%, and 100% thresholds. The protection circuit responded to over-current events within spec on both the charge and discharge sides.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-installation self-test protocol:\u003c\/strong\u003e\n    After installing this battery, allow the monitor to complete its full power-on self-test without interruption. The VITAPIA7000K runs a BMS verification routine at startup — cutting power mid-sequence triggers a false battery fault flag that persists until the device is rebooted and the test completes cleanly.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the VITAPIA7000K alarms low battery immediately after a confirmed full charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe monitor's charge IC sets its \"battery healthy\" threshold against the OEM cell's learned chemistry profile. A new replacement pack has no charge history stored in the BMS, so the monitor reads state-of-charge conservatively and triggers the low-battery alarm even when the pack is physically full. Running one complete charge-discharge cycle — charge to 100%, allow the monitor to draw the pack down through normal operation, then recharge fully — writes the calibration data the BMS needs. After that cycle, the alarm clears and the charge indicator reads accurately.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eVITAPIA7000K not completing boot sequence after battery was in storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eLi-ion cells self-discharge at roughly 1–3% per month in storage. If the pack sat long enough to drop below approximately 2.5V per cell (5.0V pack-level), the VITAPIA7000K's BMS locks out discharge entirely as a deep-discharge protection measure — the monitor will not boot. Connect the device to mains power first and leave it on charge for a minimum of four hours before attempting to run on battery alone. This allows the charge IC to apply a low-current recovery charge that brings the cell voltage back above the BMS unlock threshold before a full charge cycle begins.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381439266906,"sku":"BWCS-CMS900MX-1","price":83.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381439299674,"sku":"BWCS-CMS900MX-2","price":98.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381439332442,"sku":"BWCS-CMS900MX-3","price":109.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-CMS900MX-1.webp?v=1778900837","url":"https:\/\/batteryweb.com\/products\/trismed-vitapia7000k-type7012k-replacement-battery-74v-13500mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}