{"product_id":"urovo-i9100-replacement-battery-37v-5200mah-li-ion","title":"Urovo i9100 Barcode Scanner Replacement Battery HBL9100 3.7V 5200mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eUrovo i9100 — 3.7V Li-ion Replacement Battery (HBL9100)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 3.7V, 5200mAh lithium-ion pack replaces the OEM battery in the Urovo i9100 rugged handheld mobile computer. The i9100 is a barcode scanner used in warehouse, logistics, and retail pick-and-pack operations. Voltage and cell count match the original, so the BMS handshake proceeds without errors on a charged pack.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003ei9100 platform fit:\u003c\/strong\u003e\n    The i9100 uses a single-cell 3.7V nominal rail with a proprietary connector keyed to HBL9100 and NBL9100 packs. The BMS in this replacement mirrors the original cell configuration, so the device firmware recognises the pack and reports charge state correctly through the status bar.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through the i9100's charge and discharge cycle on the bench. The BMS held the full-charge cutoff at 4.2V and triggered low-voltage protection cleanly at 3.0V, with no false cutoffs under combined wireless radio and scan-trigger load.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-shift prep on the i9100:\u003c\/strong\u003e\n    After installing, seat the scanner in its charging cradle and run a full charge cycle before triggering any scans. The inrush current from the scan trigger is highest when the cell is near minimum — a fully charged pack prevents a BMS trip at the start of the first shift.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eScanner losing wireless connection during rapid scan bursts\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe i9100 runs both a wireless radio and a scan trigger from the same cell. During rapid barcode scanning, the combined inrush from the imager firing and the radio transmitting simultaneously causes a brief voltage sag on the cell. If the cell voltage dips below the BMS protection threshold — typically around 3.0V under load — the BMS trips and the radio drops before the device fully powers off. A fresh, fully charged 5200mAh cell holds the voltage rail steadier under that combined load than a degraded original pack would.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCradle showing a charging error after fitting the new pack\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eA charging error on the cradle display after a battery swap almost always points to contact resistance, not a faulty cell. Wipe the gold contacts on the battery base and the corresponding pins inside the cradle slot with a dry cloth, then reseat the scanner firmly until it clicks. If the error clears within 30 seconds of reseating, the contacts were the cause. If the error persists, confirm the cradle output voltage at the pins — it should read 4.2–4.5V DC before dismissing the pack as the fault.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43324704555098,"sku":"BWCS-URV910BL-1","price":38.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43324704587866,"sku":"BWCS-URV910BL-2","price":44.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43324704620634,"sku":"BWCS-URV910BL-3","price":47.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-URV910BL_1.webp?v=1778122647","url":"https:\/\/batteryweb.com\/products\/urovo-i9100-replacement-battery-37v-5200mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}