{"product_id":"valve-index-controller-replacement-battery-38v-1000mah-li-polymer","title":"AHB822048 Valve Index Controller Compatible Battery 3.8V 1000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eValve Index Controller — 3.8V Li-Polymer Replacement Battery (AHB822048)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.8V, 1000mAh Li-Polymer cell for the Valve Index Controller. It fits the motion controllers used with the Valve Index VR headset. When your original cell no longer holds charge through a play session, this is the direct swap.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eValve Index Controller fit:\u003c\/strong\u003e\n    The AHB822048 cell is specific to the Valve Index Controller housing. Both left and right controllers use the same cell format, voltage rail, and connector — one part number covers both units.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through the Valve Index Controller BMS and confirmed charge acceptance, discharge curve, and thermal response under combined wireless tracking and haptic feedback load. No false low-battery trips during initial cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFuel gauge calibration on first use:\u003c\/strong\u003e\n    After installing this cell, run one full wireless play session through to the controller's automatic cutoff before recharging. The fuel gauge IC sets its empty reference point against the first complete discharge — skipping this step causes the battery indicator to read inaccurately for subsequent sessions.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the Valve Index Controller fuel gauge jumps after a cell swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe Valve Index Controller uses a coulomb-counting fuel gauge IC that tracks charge by measuring current in and out of the cell over time. When you swap in a new cell, the IC has no discharge history for it and defaults to an estimated state of charge. This causes the percentage reading to jump or display inconsistently during the first few sessions. After one full discharge-to-cutoff cycle, the IC locks onto the new cell's actual capacity and the gauge stabilises.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eController drops wireless connection before the battery indicator reaches empty\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when simultaneous wireless transmission and haptic motor activation pull current faster than the cell can supply it at low charge states. Voltage briefly sags below the BMS cutoff threshold, and the controller disconnects — even though the reported battery percentage hasn't hit zero yet. On a fresh cell, this is most common in the first two to three cycles before the cell's internal resistance settles. If disconnects persist past five cycles, check that the cell connector is fully seated, as a loose contact increases effective resistance under load.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43377532764250,"sku":"BWCS-VIC100SL-1","price":30.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43377532797018,"sku":"BWCS-VIC100SL-2","price":35.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43377532829786,"sku":"BWCS-VIC100SL-3","price":39.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-VIC100SL-1.webp?v=1778767310","url":"https:\/\/batteryweb.com\/products\/valve-index-controller-replacement-battery-38v-1000mah-li-polymer","provider":"BatteryWeb","version":"1.0","type":"link"}