{"product_id":"vanguard-740012-replacement-battery-6v-2300mah-alkaline","title":"Vanguard 740012 Door Lock Compatible Battery 6V 2300mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eVanguard 740012 — 6V Alkaline Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 6V alkaline replacement battery rated at 2300mAh (13.8Wh) for the Vanguard 740012 electronic door lock. It fits residential and commercial entry points using the 740012 platform. Drop this in when the original power depletes and the lock stops responding to keypad, remote, or keycard input.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eVanguard 740012 lock platform:\u003c\/strong\u003e\n    The 740012 uses a 6V rail to drive the motor, logic board, and wireless receiver in a single power loop. A battery short of that voltage threshold causes partial or complete access failure — keypad lights may stay on while the motor refuses to actuate.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this battery against the 740012 BMS handshake sequence. Voltage under motor-start load held steady, the controller accepted the pack without fault codes, and all access methods initialised cleanly.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-swap access verification:\u003c\/strong\u003e\n    After fitting this battery, test every access method — keypad, Bluetooth, and keycard — before closing the door. The 740012 runs a firmware handshake after any power interruption, and that sequence must complete fully before the lock will accept all credential types.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the 740012 motor won't actuate even with a full battery installed\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe 740012 draws a short high-current spike when the deadbolt motor fires. If the battery's internal resistance is too high — common in aged or storage-depleted alkaline cells — voltage sags below the motor-start threshold during that spike. The controller reads this as a fault and blocks actuation to protect the mechanism. Use a battery with confirmed fresh cell chemistry and check that terminal contact is clean and fully seated before testing.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eLow battery warning appears immediately after fitting a new battery\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis usually means the cells in the pack read below the lock's detection threshold at the moment of first contact. It happens most often with batteries that have been sitting in storage and have drifted from their nominal 6V open-circuit voltage. Check polarity first — reversed cells produce a near-zero reading that triggers the warning instantly. If polarity is correct, measure the battery's open-circuit voltage with a multimeter; it should read at or above 6.0V before installation.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43360204423258,"sku":"BWCS-SDL500SL-1","price":36.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43360204456026,"sku":"BWCS-SDL500SL-2","price":42.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43360204488794,"sku":"BWCS-SDL500SL-3","price":47.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-SDL500SL-1.webp?v=1778610960","url":"https:\/\/batteryweb.com\/products\/vanguard-740012-replacement-battery-6v-2300mah-alkaline","provider":"BatteryWeb","version":"1.0","type":"link"}