{"product_id":"vivo-x6-replacement-battery-38v-2400mah-li-polymer","title":"Vivo X6 Replacement Battery B-91 3.8V 2400mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eVivo X6 Series — 3.8V Li-Polymer Replacement Battery (B-91)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.8V, 2400mAh Li-Polymer replacement battery for the Vivo X6, X6D, X6D Dual SIM TD-LTE, X6A, and compatible variants. It replaces the original B-91 cell when the existing battery has degraded through repeated charge cycles or no longer holds charge. Capacity figure is drawn from product data: 2400mAh (9.12Wh).\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eX6 series cell compatibility:\u003c\/strong\u003e\n    The X6, X6D, and X6A share the same 3.8V voltage rail, connector pinout, and BMS handshake protocol, which is why one B-91 cell spans all these variants. Swapping to a different voltage or connector spec will cause BMS rejection or a boot loop.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge and discharge cycles on X6-series hardware. The BMS accepted the new cell without fault flags, and the protection circuit engaged correctly at both the low-voltage cutoff and high-voltage ceiling.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFuel gauge recalibration on first use:\u003c\/strong\u003e\n    On first use after installation, disable fast charging for one complete discharge-charge cycle. This lets the fuel gauge IC build an accurate discharge curve against the new cell before high-current charging pushes power into an uncalibrated state.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSudden shutdown at 20–30% on the replacement cell\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eAfter a cell swap, the fuel gauge IC still holds the discharge curve it mapped to the old, degraded cell. The new cell has a steeper voltage cliff under modem or display load than the IC expects, so it reports 25% remaining right up until the cell voltage collapses under load. The phone cuts out because the actual cell voltage drops below the BMS floor even though the percentage counter hasn't caught up. One full discharge-to-shutdown and uninterrupted charge cycle forces the coulomb counter to remap to the new cell and eliminates these phantom shutdowns.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eUSB fast charge not working on the first cycle after replacement\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eVivo's charge IC performs a handshake with the BMS on the first charge after a cell change. If the BMS returns unexpected impedance readings — common when a new high-impedance cell is installed cold — the IC defaults to standard 5V\/1A charging as a safety measure. This is not a fault with the battery or charger. Fully discharge the phone to automatic shutdown once, then charge uninterrupted to 100% using the original Vivo adapter, and the charge IC will accept the fast-charge protocol on the next session.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43404132712538,"sku":"BWCS-BYX600SL-1","price":24.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43404132745306,"sku":"BWCS-BYX600SL-2","price":27.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43404132778074,"sku":"BWCS-BYX600SL-3","price":30.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BYX600SL-1.webp?v=1779369037","url":"https:\/\/batteryweb.com\/products\/vivo-x6-replacement-battery-38v-2400mah-li-polymer","provider":"BatteryWeb","version":"1.0","type":"link"}