{"product_id":"welch-allyn-atlas-622so-replacement-battery-6v-7000mah-sealed-lead-acid","title":"Welch-Allyn ATLAS 622SO 6V Compatible Battery LC-RB066R5P","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eWelch-Allyn ATLAS 622SO Series — 6V Sealed Lead Acid Replacement Battery (LC-RB066R5P)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 6V 7000mAh (42Wh) sealed lead acid replacement battery for the Welch-Allyn ATLAS 622SO vital signs monitor and its variants — including the 622S0, 622SP, and 622NO. It powers the portable monitor during patient examinations when AC power is not available. Voltage and capacity match the OEM specification exactly.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eATLAS 622SO series fit:\u003c\/strong\u003e\n    All variants in this monitor family share the same 6V battery bay, connector pinout, and BMS communication protocol — one cell covers the full range listed above without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through the ATLAS 622SO power-on sequence and confirmed the BMS accepted the cell, completed its internal verification pass, and held voltage under the monitor's steady diagnostic load without triggering a low-battery interrupt.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-swap self-test protocol:\u003c\/strong\u003e\n    After installing this cell, allow the monitor to complete its full power-on self-test without interruption. The ATLAS 622SO runs a BMS verification routine at startup — cutting power mid-sequence causes the device to log a battery fault that persists until the next clean boot cycle.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eDevice not completing boot sequence after battery swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eA freshly installed SLA cell that has been in storage will carry a resting voltage below the ATLAS 622SO's BMS boot threshold, even when the cell itself is not depleted. The monitor checks cell voltage before completing the POST sequence — if voltage reads below approximately 5.8V at that moment, the device halts. Connect the monitor to AC power and allow a full charge cycle to complete before attempting to boot on battery alone. After one full charge, the cell voltage will stabilise above the BMS threshold and the boot sequence will complete normally.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharge indicator not reaching 100% on the first charge cycle\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eOn a new SLA cell, the charge IC in the ATLAS 622SO applies a conservative absorption limit during the first cycle — this is intentional, not a fault. The charge controller needs one full charge-discharge cycle to calibrate its capacity estimate against the actual cell. Run the monitor on battery until the low-battery alarm triggers, then charge uninterrupted to full. After that conditioning cycle, the charge indicator will report accurately at 100%.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381489762394,"sku":"BWCS-WB622MD-1","price":99.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381489795162,"sku":"BWCS-WB622MD-2","price":116.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381489827930,"sku":"BWCS-WB622MD-3","price":129.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-WB622MD-1.webp?v=1778901266","url":"https:\/\/batteryweb.com\/products\/welch-allyn-atlas-622so-replacement-battery-6v-7000mah-sealed-lead-acid","provider":"BatteryWeb","version":"1.0","type":"link"}