{"product_id":"wella-xpert-hs50-replacement-battery-36v-1200mah-ni-mh","title":"Wella Xpert HS50 Replacement Battery 3.6V 1200mAh KR600","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eWella Xpert HS50 — 3.6V Ni-MH Replacement Battery (KR600)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.6V, 1200mAh Ni-MH replacement battery for the Wella Xpert HS50 cordless hair clipper. It slots into the original battery bay and mates with the same connector and BMS handshake as the factory cell. When the original cell degrades and the clipper loses cutting power or refuses to charge, this is the correct replacement part.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eXpert HS50 fitment:\u003c\/strong\u003e\n    The HS50 runs a 3.6V single-cell Ni-MH configuration with a fixed charge termination voltage. Swapping chemistry — even at the same nominal voltage — trips the charge controller. This replacement matches that cell format exactly, so the onboard charge circuit behaves normally.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this battery through the HS50 charge dock and confirmed BMS cutoff triggered at the correct termination point. The motor reached full speed immediately and held consistent torque through the discharge curve without premature shutdown.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eClipper motor load tip:\u003c\/strong\u003e\n    Ni-MH cells in clippers degrade faster when stored fully discharged between uses. Run the clipper until the motor noticeably slows, then charge immediately — Ni-MH does not recover well from sitting at zero volts for extended periods.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the HS50 motor slows before the charge indicator reaches empty\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells experience a voltage sag under motor load before the battery reaches true cutoff. The HS50's charge indicator reads resting voltage, not loaded voltage, so it can show a partial charge while the cell is already sagging below what the motor needs to run at full speed. This is most noticeable in cells that have gone through many shallow cycles — internal resistance climbs and the sag deepens. Replacing the cell restores a flat discharge curve and eliminates the premature slowdown.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eClipper not charging after cleaning product contact with the dock\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eSpray cleaners and blade oils that reach the charging contacts leave a residue that oxidises the contact surface. The dock may appear seated correctly but voltage transfer drops below the threshold the BMS needs to initiate a charge cycle. Clean both the dock contacts and the battery contacts with a dry cotton swab, then reseat the clipper firmly. If charge resumes, the fault was contact oxidation — not the battery or the dock circuitry.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43416127832154,"sku":"BWCS-WXH500SL-1","price":24.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43416127864922,"sku":"BWCS-WXH500SL-2","price":27.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43416127897690,"sku":"BWCS-WXH500SL-3","price":30.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-WXH500SL-1.webp?v=1779760331","url":"https:\/\/batteryweb.com\/products\/wella-xpert-hs50-replacement-battery-36v-1200mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}