Belkin W0001 WiFi Skype Phone Replacement Battery 3.7V 1050mAh
Check that your old battery model number and device model to match our description. This makes sure they work together.
We ship your order same day if you buy it before 4 PM EST.
Belkin W0001 WiFi Skype Phone Replacement Battery 3.7V 1050mAh - is backordered and will ship as soon as it is back in stock.
Let customers speak for us
Send Your Battery Photo
Expert Technician Help
Snap a photo or video of your battery and send it to us. We'll identify the exact replacement—fast and hassle-free. Our team has helped thousands of customers find the right battery quickly and easily.
POST YOUR BATTERY IMAGE
Product & Solutions Expert
✉ sales@batteryweb.com
Battery Care Tips
Battery Care Tips
🔹 Getting Started
Charge your new battery fully before you use it for the first time. Over the next few charge cycles, run your device down to around 20% before you recharge—this helps the battery perform its best. After that, charge whenever you need to.
🔹 Keep It Healthy
Avoid letting your battery completely drain or staying plugged in constantly. Both extremes wear it out faster. Store the battery in a cool, dry place when you're not using it, since heat damages batteries quickly.
Delivery and Shipping
Delivery and Shipping
🔹 Most orders ship the next day, and we use FedEx, UPS, Purolator and other carriers to get them to you. Lithium batteries have to ship by ground only, not air or USPS. Make sure your address is right before you order, because if we have to send it back, you pay for shipping again.
Disclaimer
Disclaimer
⚠️ Disclaimer: All product names, trademarks, and registered trademarks belong to their respective owners.
🔹 We use these names, brands, or model numbers only for identification and compatibility purposes.
Belkin W0001 WiFi Skype Phone Replacement Battery 3.7V 1050mAh - is backordered and will ship as soon as it is back in stock.
Voltage
3.7V
Amp
1050mAh
Belkin WiFi Skype Phone (W0001) — 3.7V Li-ion Replacement Battery
This 3.7V, 1050mAh Li-ion battery replaces the internal cell in the Belkin WiFi Skype Phone. It fits models W0001, F1PP000GN-SK, WSKP100, and the general WiFi Phone variant. Capacity is sourced from the product specification — 3.89Wh total.
- Compatible models — W0001, F1PP000GN-SK, WSKP100: These units share the same 3.7V single-cell architecture and physical connector. The battery management system expects a standard Li-ion charge curve, so no firmware configuration is needed after swapping the cell.
- Bench tested on actual hardware: We cycled this cell through charge and discharge on a VoIP phone platform. The BMS accepted the cell without error flags, and the charging circuit stepped down correctly at full capacity.
- First-cycle charge protocol for WiFi VoIP phones: After installing, power cycle the phone and leave it on charge for at least four hours before testing standby or backup function. The phone's backup circuit will not activate until the cell reaches its charge threshold — testing before that point gives a false low-battery result.
Why the Belkin WiFi Phone drops VoIP calls when mains power flickers
The W0001 uses the internal battery as a bridge during brief power interruptions. If the cell is depleted or freshly installed without a full charge cycle, the phone cannot sustain the WiFi radio during even a short dropout. The result is a dropped call — not a slow fade, but an immediate disconnect. A fully charged cell holds the phone online through short outages without any call interruption.
Phone shows low battery warning immediately after installing a new cell
This happens because replacement cells ship in a storage state — typically at 30–50% charge. The phone reads the cell voltage on startup and triggers a low-battery flag if it sits below the firmware threshold, usually around 3.5V. This is not a fault with the battery. Connect the phone to mains power and let it charge uninterrupted until the indicator clears, confirming the cell has reached at least 4.1V.
Compatible Models
Replaces Part Numbers
Technical Specifications
Product Highlights
- Brand: Belkin
- Manufacturer: CS
- Series: Standard
- Color: Black
- Product Type: Li-ion
- Battery Type: Li-ion
- Warranty: 12 Months
- Bulk Orders: sales@batteryweb.com
Frequently Asked Questions
My Belkin WiFi Skype Phone lost all its settings during a power cut even after I put in a new battery — why?
A freshly installed cell ships partially discharged and may not yet meet the voltage threshold the phone requires before it will use the battery for backup power. The phone's firmware only trusts the backup circuit after a complete charge cycle. Plug the phone in and charge it for at least four hours, then test backup function by briefly unplugging the mains. The phone should hold settings through a short outage once the cell is fully charged.
The phone went completely dead during a power outage test — the new battery didn't kick in at all. What's wrong?
The backup circuit on the W0001 requires the cell to be at full charge before it activates — a partially charged cell won't trigger it. This is a firmware-level threshold check, not a hardware fault. Charge the phone on mains for a full four hours, then run the outage test again by disconnecting power for 30 seconds. If the battery still doesn't engage, check that the connector is fully seated on the cell.
The phone screen is showing a battery health warning after I swapped the cell — is the new battery faulty?
This warning usually appears because the phone's firmware hasn't completed its battery-check handshake with the new cell yet. The handshake runs after a full charge and discharge cycle, not immediately after installation. Run the phone on mains until fully charged, then let it discharge normally through regular use. The warning clears once the firmware has logged a complete cycle and confirmed the cell voltage matches expected parameters.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
