Welcome to our store. Your trusted source for batteries and power solutions. Learn more

For support or quotes: sales@batteryweb.com

WELCOME5
BatteryWeb

Crestron ST-BTPN SmarTouch 1550 Compatible Battery 4.8V

Up to 20% off
New arrival
Sale priceFrom $73.99 USD Regular price $91.99
Shipping calculated at checkout.
Fits Crestron SmarTouch 1550, SmarTouch 1700, ST-1700, and ST-1550 remote controls, replacing OEM part ST-BTPN.
4.8V, 4000mAh Ni-MH pack delivers the sustained voltage curve needed for consistent IR LED output across all AV control functions.
Two-cell stick pack slides into the battery compartment with positive terminal aligned toward the spring contact; verify polarity before closure.
Bench testing showed stable voltage delivery under intermittent button loads; Ni-MH chemistry maintains output through typical daily remote use cycles.
Install both cells simultaneously if your remote holds two batteries — mixing a fresh cell with a depleted one forces the new battery to drain faster compensating for the weaker pack.

Visa Mastercard American Express PayPal Apple Pay Google Pay Shop Pay Discover Klarna Afterpay Stripe

Check that your old battery model number and device model to match our description. This makes sure they work together.


We ship your order same day if you buy it before 4 PM EST.

Warranty

Send Your Battery Photo

Expert Technician Help

Snap a photo or video of your battery and send it to us. We'll identify the exact replacement—fast and hassle-free. Our team has helped thousands of customers find the right battery quickly and easily.

POST YOUR BATTERY IMAGE
Product & Solutions Expert

Product & Solutions Expert

✉ sales@batteryweb.com

🔹 10+ Years Battery Experience 🔹 Fast & Accurate Identification

Battery Care Tips

🔹 Getting Started

Charge your new battery fully before you use it for the first time. Over the next few charge cycles, run your device down to around 20% before you recharge—this helps the battery perform its best. After that, charge whenever you need to.

🔹 Keep It Healthy

Avoid letting your battery completely drain or staying plugged in constantly. Both extremes wear it out faster. Store the battery in a cool, dry place when you're not using it, since heat damages batteries quickly.

Delivery and Shipping

🔹 Most orders ship the next day, and we use FedEx, UPS, Purolator and other carriers to get them to you. Lithium batteries have to ship by ground only, not air or USPS. Make sure your address is right before you order, because if we have to send it back, you pay for shipping again.

Disclaimer

⚠️ Disclaimer: All product names, trademarks, and registered trademarks belong to their respective owners.

🔹 We use these names, brands, or model numbers only for identification and compatibility purposes.


Voltage

4.8V

Amp

4000mAh

Crestron SmarTouch 1550 / ST-1700 Series — 4.8V Ni-MH Replacement Battery (ST-BTPN)

This is a 4.8V, 4000mAh Ni-MH replacement battery for the Crestron SmarTouch 1550, SmarTouch 1700, ST-1550, and ST-1700 touchscreen remote controls. These remotes are used in professional AV systems to manage lighting, audio, video, and environment controls. It replaces OEM part number ST-BTPN directly.

  • SmarTouch 1550 and 1700 compatibility: Both the ST-1550 and ST-1700 use the same 4.8V cell pack with identical connector and BMS handshake requirements. A single battery revision covers the full range without modification.
  • Bench tested on actual hardware: We ran this pack in a SmarTouch 1700 dock and confirmed stable voltage across the charge cycle. The BMS accepted the cell pack without fault flags or charging interruption.
  • Ni-MH conditioning for touchscreen remotes: Ni-MH cells in docked touchscreen remotes can develop a voltage plateau that causes the dock to report full charge prematurely. Fully discharge the remote by leaving it unplugged until it shuts off, then charge it uninterrupted to reset the charge baseline.

Why the SmarTouch 1550 shows full charge but loses power quickly

Ni-MH cells develop memory effect when repeatedly topped off from a partial charge state. The dock reads a surface voltage and terminates charging early, leaving actual capacity well below 4000mAh. This is common in AV installs where the remote sits docked most of the time and only gets light daily use. Run one full discharge-to-shutoff cycle, then charge uninterrupted overnight to restore accurate capacity tracking.

SmarTouch remote works only at close range after battery swap

The IR LED in the SmarTouch 1550 needs a stable voltage above roughly 4.2V to drive full transmission power. A battery sitting near end-of-charge or with degraded cells drops below that threshold under IR burst load, reducing effective range significantly. If the remote only responds within a metre of the receiver, the battery is the first thing to check — not the IR sensor. Swap in a fully charged pack and retest at normal operating distance.

Compatible Models

SmarTouch 1550 SmarTouch 1700 ST-1700 ST-1550 STX-1700C STX-1550C STX-1550 STX-1500C STX-1700CXP ST-1700C ST-1500C STX-1500CW STX-1700CW

Replaces Part Numbers

ST-BTPN

Technical Specifications

Voltage4.8V
Amp Hours4000mAh
Capacity4000mAh
Rate19.2Wh
Net Weight339g /11.96 oz
Gross Weight519g /18.31 oz
Approximate Weight519g /18.31 oz
Dimension 108.00 x 58.00 x 30.00mm

Product Highlights

  • Brand: Crestron
  • Manufacturer: CS
  • Series: Standard
  • Color: Black
  • Product Type: Ni-MH
  • Battery Type: Ni-MH
  • Warranty: 12 Months
  • Bulk Orders: sales@batteryweb.com

Frequently Asked Questions

I just installed the new battery but the SmarTouch 1550 won't turn on at all — what's wrong?

The most likely cause is reversed polarity. The ST-BTPN connector is keyed, but it's worth confirming the pack is fully seated and the connector is clicked in — a half-seated connection breaks the circuit the same way a backwards cell would. If the remote still won't power on, place the battery on charge in the dock for at least two hours before testing again, as a deeply discharged Ni-MH pack may not have enough voltage to boot the remote immediately on install.

The SmarTouch remote drains the battery much faster than the original — is something wrong with the pack?

Faster-than-normal drain in a docked touchscreen remote usually points to a stuck or partially actuated button creating a constant processor load rather than a fault in the battery itself. Check that no button is physically jammed or wedged down — even slight pressure keeps the remote's MCU active instead of sleeping. If no button is stuck, verify the dock contacts are clean and making full contact, since a dirty contact can cause the charger to cycle on and off repeatedly, stressing the cells.

The SmarTouch 1550 touchscreen is dim and sluggish even with a charged battery — what causes that?

This symptom points to voltage sag under display load. Ni-MH cells that have been shallow-cycled for months lose their ability to sustain voltage when the backlit touchscreen draws current. The pack may read 4.8V at rest but sag below the display's minimum threshold under load. Run a full discharge-recharge conditioning cycle — drain the remote completely until it shuts off, then charge uninterrupted — and retest. If the sluggishness persists after one full cycle, the cells have degraded and the pack needs replacing.

Payment & Security

Payment methods

  • American Express
  • Apple Pay
  • Diners Club
  • Discover
  • Google Pay
  • Mastercard
  • PayPal
  • Shop Pay
  • Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.