Welcome to our store. Proudly serving customers across North America for years. Learn more

For support or quotes: sales@batteryweb.com

WELCOME10
BatteryWeb

ViewSonic Zoompad MLP486890 Compatible Battery 3.7V 3200mAh

Up to 21% off
New arrival
Sale priceFrom $26.99 USD Regular price $33.99
Shipping calculated at checkout.
Fits ViewSonic Zoompad tablet; replaces OEM part number MLP486890 battery.
3.7V 3200mAh Li-Polymer cell restores full charge cycles to the Zoompad after degradation.
Connector type matches original slot orientation; locking tab aligns with the tablet housing.
We bench tested this cell on a Zoompad charge cycle; BMS accepted the pack without fault codes.
After installation, run one full discharge to automatic shutoff then charge uninterrupted to 100% — this resets the fuel gauge IC calibration against the new cell and resolves inaccurate percentage display.

Visa Mastercard American Express PayPal Apple Pay Google Pay Shop Pay Discover Klarna Afterpay Stripe

Check that your old battery model number and device model to match our description. This makes sure they work together.


We ship your order same day if you buy it before 4 PM EST.

Warranty

Send Your Battery Photo

Expert Technician Help

Snap a photo or video of your battery and send it to us. We'll identify the exact replacement—fast and hassle-free. Our team has helped thousands of customers find the right battery quickly and easily.

POST YOUR BATTERY IMAGE
Product & Solutions Expert

Product & Solutions Expert

✉ sales@batteryweb.com

🔹 10+ Years Battery Experience 🔹 Fast & Accurate Identification

Battery Care Tips

🔹 Getting Started

Charge your new battery fully before you use it for the first time. Over the next few charge cycles, run your device down to around 20% before you recharge—this helps the battery perform its best. After that, charge whenever you need to.

🔹 Keep It Healthy

Avoid letting your battery completely drain or staying plugged in constantly. Both extremes wear it out faster. Store the battery in a cool, dry place when you're not using it, since heat damages batteries quickly.

Delivery and Shipping

🔹 Most orders ship the next day, and we use FedEx, UPS, Purolator and other carriers to get them to you. Lithium batteries have to ship by ground only, not air or USPS. Make sure your address is right before you order, because if we have to send it back, you pay for shipping again.

Disclaimer

⚠️ Disclaimer: All product names, trademarks, and registered trademarks belong to their respective owners.

🔹 We use these names, brands, or model numbers only for identification and compatibility purposes.


Voltage

3.7V

Amp

3200mAh

ViewSonic Zoompad — 3.7V Li-Polymer Replacement Battery (MLP486890)

This is a 3.7V 3200mAh Li-Polymer battery for the ViewSonic Zoompad tablet. It replaces part number MLP486890 when the original cell no longer holds a usable charge. Capacity matches the factory specification at 11.84Wh.

  • Zoompad platform fit: The Zoompad uses a single-cell Li-Polymer pack with a specific connector pinout and BMS handshake tied to the charge IC on the motherboard. This battery matches that voltage rail and connector so the charge controller accepts it without a fault state.
  • Bench tested on actual hardware: We cycled this cell through charge and discharge on a Zoompad unit. The BMS reported clean voltage curves, no overcurrent trips, and the charge IC accepted the cell from the first connection.
  • Fuel gauge calibration after swap: After fitting this battery, run the tablet down to automatic shutoff, then charge uninterrupted to 100% without using the device. This single full cycle resets the fuel gauge IC calibration against the new cell and clears the inaccurate percentage readings that appear immediately after installation.

Zoompad shutting down at 15–25% battery remaining

The Zoompad's combined display and WiFi load draws a current spike that can pull cell voltage below the BMS cutoff threshold before the fuel gauge hits zero. This happens most often when the fuel gauge IC is calibrated to a worn cell and misreads actual capacity on a new one. The result is a hard shutdown even though the percentage counter shows charge remaining. One full discharge-to-shutoff cycle followed by an uninterrupted charge to 100% realigns the IC — after that, the shutoff point should track correctly down to around 3.4V.

Fast charging not available after battery replacement

Some Zoompad units use a proprietary charge negotiation handshake between the charge IC and the battery BMS. On the first cycle after a swap, the charge controller may default to standard 5V charging while it verifies the new cell parameters. This is not a fault — the IC is validating voltage response before stepping up charge current. Complete one full charge cycle using the original ViewSonic charger and the fast charge profile typically resumes from the second cycle onward.

Compatible Models

Zoompad

Replaces Part Numbers

MLP486890

Technical Specifications

Voltage3.7V
Amp Hours3200mAh
Capacity3200mAh
Rate11.84Wh
Net Weight62g /2.19 oz
Gross Weight97g /3.42 oz
Approximate Weight97g /3.42 oz
Dimension 90.00 x 65.30 x 4.70mm

Product Highlights

  • Brand: ViewSonic
  • Manufacturer: CS
  • Series: Standard
  • Color: Black
  • Product Type: Li-Polymer
  • Battery Type: Li-Polymer
  • Warranty: 12 Months
  • Bulk Orders: sales@batteryweb.com

Frequently Asked Questions

My Zoompad says 60% battery but shuts off completely — why?

The fuel gauge IC was calibrated to the worn original cell, so its capacity map no longer matches the new battery's voltage curve. Under the combined load of the display and active WiFi, the cell voltage dips below the BMS cutoff point before the percentage counter reaches zero. Run the tablet down to automatic shutoff, then charge uninterrupted to 100% without using it during that charge. After that single full cycle, the IC recalibrates and the shutoff point tracks correctly to around 3.4V.

The Zoompad percentage jumps around — shows 80%, then suddenly drops to 45% in minutes

This is fuel gauge drift — the IC is estimating capacity from a calibration map built on the old degraded cell, so readings on the new battery are erratic. The percentage counter loses accuracy when the reference curve no longer matches actual cell behaviour. Fix it with one complete discharge to automatic shutoff followed by a full uninterrupted charge to 100%. After that cycle the gauge reads against the new cell's actual voltage curve and stabilises.

Fast charging stopped working after I swapped the battery on my Zoompad

After a battery swap, the charge IC defaults to standard 5V input on the first cycle while it validates the new cell's voltage response — this is the controller protecting the cell, not a compatibility fault. Use the original ViewSonic charger for the first full charge and do not interrupt it. Fast charge negotiation typically resumes from the second charge cycle once the IC has logged a complete accepted charge from the new cell.

Payment & Security

Payment methods

  • American Express
  • Apple Pay
  • Diners Club
  • Discover
  • Google Pay
  • Mastercard
  • PayPal
  • Shop Pay
  • Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.