Welcome to our store. Your trusted source for batteries and power solutions. Learn more

For support or quotes: sales@batteryweb.com

WELCOME5
BatteryWeb

Pentair Mobiltouch 2 Compatible Battery 7.4V 2200mAh 520815Z

Up to 21% off
New arrival
Sale priceFrom $30.99 USD Regular price $38.99
Shipping calculated at checkout.
Fits Pentair Mobiltouch 2 wireless remote, part number 520815Z direct replacement.
7.4V lithium-polymer pack delivers 2200mAh capacity, restoring full remote range to your pool control system.
Connector seats into the battery compartment with positive terminal forward, secured by the original slot latch.
We ran charge cycles on the Pentair platform — BMS accepts the cell without fault codes on first insertion.
After installing this cell, wait 60 seconds before operating the remote, as the wireless link needs time to re-establish with your IntelliTouch hub.

Visa Mastercard American Express PayPal Apple Pay Google Pay Shop Pay Discover Klarna Afterpay Stripe

Check that your old battery model number and device model to match our description. This makes sure they work together.


We ship your order same day if you buy it before 4 PM EST.

Warranty

Send Your Battery Photo

Expert Technician Help

Snap a photo or video of your battery and send it to us. We'll identify the exact replacement—fast and hassle-free. Our team has helped thousands of customers find the right battery quickly and easily.

POST YOUR BATTERY IMAGE
Product & Solutions Expert

Product & Solutions Expert

✉ sales@batteryweb.com

🔹 10+ Years Battery Experience 🔹 Fast & Accurate Identification

Battery Care Tips

🔹 Getting Started

Charge your new battery fully before you use it for the first time. Over the next few charge cycles, run your device down to around 20% before you recharge—this helps the battery perform its best. After that, charge whenever you need to.

🔹 Keep It Healthy

Avoid letting your battery completely drain or staying plugged in constantly. Both extremes wear it out faster. Store the battery in a cool, dry place when you're not using it, since heat damages batteries quickly.

Delivery and Shipping

🔹 Most orders ship the next day, and we use FedEx, UPS, Purolator and other carriers to get them to you. Lithium batteries have to ship by ground only, not air or USPS. Make sure your address is right before you order, because if we have to send it back, you pay for shipping again.

Disclaimer

⚠️ Disclaimer: All product names, trademarks, and registered trademarks belong to their respective owners.

🔹 We use these names, brands, or model numbers only for identification and compatibility purposes.


Voltage

7.4V

Amp

2200mAh

Pentair Mobiltouch 2 — 7.4V Li-Polymer Replacement Battery (520815Z)

This 7.4V, 2200mAh lithium-polymer battery replaces OEM part 520815Z in the Pentair Mobiltouch 2 handheld wireless controller. It also fits the IntelliTouch Control System and MobileTouch II Wireless Controller. The remote uses this cell to send commands to pumps, heaters, and lighting across the pool automation network.

  • Mobiltouch 2 / MobileTouch II platform fit: These models share the same 7.4V two-cell Li-Polymer pack, connector pinout, and BMS communication protocol. One battery part number covers all three listed controllers because the power architecture is identical across the IntelliTouch wireless controller family.
  • Bench tested on actual hardware: We cycled this pack through charge and discharge on the bench and confirmed the BMS reported state-of-charge correctly to the controller firmware, with no voltage cutoff triggering under normal polling loads.
  • Re-join delay after swap: After fitting this battery, hold off on testing for at least 60 seconds. The Mobiltouch 2 runs a mesh network re-join sequence on every power cycle — commands sent before that sequence completes will not reach the IntelliTouch system.

Why the Mobiltouch 2 goes offline immediately after a battery swap

Cutting power to the remote clears its active session with the IntelliTouch receiver. When the new battery is installed, the controller broadcasts a re-join request and waits for acknowledgement from the base system. This handshake takes up to 60 seconds under normal RF conditions. If you press buttons before it completes, the controller silently drops the command — the display may look active, but nothing reaches the pump or heater.

Low battery alert showing immediately after fitting a new cell

A brand-new replacement cell that has been in storage for several months can sit at 3.5–3.7V per cell — below the alert threshold the Mobiltouch 2 firmware checks on boot. The controller reads open-circuit voltage before the pack settles and flags it as low. Plug the remote into its dock charger and allow a full charge cycle before use. Once the pack reaches 4.2V per cell, the alert clears and does not return.

Compatible Models

Mobiltouch 2 IntelliTouch(R) Control System MobileTouch(R) II Wireless Controller

Replaces Part Numbers

520815Z

Technical Specifications

Voltage7.4V
Amp Hours2200mAh
Capacity2200mAh
Rate16.28Wh
Net Weight78g /2.75 oz
Gross Weight103g /3.63 oz
Approximate Weight103g /3.63 oz
Dimension 70.00 x 50.20 x 10.00mm

Product Highlights

  • Brand: Pentair
  • Manufacturer: CS
  • Series: Standard
  • Color: Blue
  • Product Type: Li-Polymer
  • Battery Type: Li-Polymer
  • Warranty: 12 Months
  • Bulk Orders: sales@batteryweb.com

Frequently Asked Questions

The Mobiltouch 2 screen comes on after the battery swap but none of my pumps or lights respond — what's wrong?

The remote lost its active session with the IntelliTouch receiver when power was cut. On restart it runs a mesh re-join sequence that takes up to 60 seconds before commands go through. Wait a full minute after installing the battery, then test. If the remote still doesn't control the system after 60 seconds, move closer to the IntelliTouch control panel and retry — RF range drops briefly during the re-join window.

My new 520815Z battery seems to drain noticeably faster than the original did — is something wrong with the cell?

This is usually a polling interval issue, not a faulty cell. If the IntelliTouch system is set to check the remote's status frequently, or if the remote is sitting at the edge of RF range and retransmitting commands, current draw rises and the pack depletes faster than expected. Check the IntelliTouch app or keypad settings for the wireless controller polling frequency and reduce it if possible. Also confirm the remote is stored within reliable RF range of the receiver — constant retransmission is the most common cause of shortened charge cycles on this platform.

The Mobiltouch 2 won't reconnect to the IntelliTouch system even after waiting the full 60 seconds — how do I fix this?

A prolonged power interruption — such as a deeply discharged original battery — can cause the IntelliTouch receiver to drop the remote from its paired device list entirely. A simple re-join sequence won't recover that. Go into the IntelliTouch control panel or app, navigate to the wireless controller pairing section, and re-pair the Mobiltouch 2 as a new device. Once pairing completes, the remote resumes full control of all assigned circuits.

Payment & Security

Payment methods

  • American Express
  • Apple Pay
  • Diners Club
  • Discover
  • Google Pay
  • Mastercard
  • PayPal
  • Shop Pay
  • Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.