Welcome to our store. Your trusted source for batteries and power solutions. Learn more

For support or quotes: sales@batteryweb.com

WELCOME5
BatteryWeb

Nuvision 10.1" Replacement Battery 3.7V 3750mAh

Up to 20% off
New arrival
Sale priceFrom $32.99 USD Regular price $40.99
Shipping calculated at checkout.
Fits Nuvision 10.1" tablet model TM1088C, replaces OEM battery 1ICP3/90/128 1S1P.
This 3.7V lithium-polymer cell delivers 3750mAh capacity, restoring full charge cycles to the display and processor.
Connector slides straight into the battery slot with a single locking tab; orientation marked on the cell itself.
We bench-tested this pack across five full charge cycles with the tablet's WiFi and screen active; BMS accepted the handshake on first insertion.
After installation, run one full discharge to automatic shutoff then charge uninterrupted to 100% — this resets the fuel gauge calibration and eliminates inaccurate percentage display after the swap.

Visa Mastercard American Express PayPal Apple Pay Google Pay Shop Pay Discover Klarna Afterpay Stripe

Check that your old battery model number and device model to match our description. This makes sure they work together.


We ship your order same day if you buy it before 4 PM EST.

Warranty

Send Your Battery Photo

Expert Technician Help

Snap a photo or video of your battery and send it to us. We'll identify the exact replacement—fast and hassle-free. Our team has helped thousands of customers find the right battery quickly and easily.

POST YOUR BATTERY IMAGE
Product & Solutions Expert

Product & Solutions Expert

✉ sales@batteryweb.com

🔹 10+ Years Battery Experience 🔹 Fast & Accurate Identification

Battery Care Tips

🔹 Getting Started

Charge your new battery fully before you use it for the first time. Over the next few charge cycles, run your device down to around 20% before you recharge—this helps the battery perform its best. After that, charge whenever you need to.

🔹 Keep It Healthy

Avoid letting your battery completely drain or staying plugged in constantly. Both extremes wear it out faster. Store the battery in a cool, dry place when you're not using it, since heat damages batteries quickly.

Delivery and Shipping

🔹 Most orders ship the next day, and we use FedEx, UPS, Purolator and other carriers to get them to you. Lithium batteries have to ship by ground only, not air or USPS. Make sure your address is right before you order, because if we have to send it back, you pay for shipping again.

Disclaimer

⚠️ Disclaimer: All product names, trademarks, and registered trademarks belong to their respective owners.

🔹 We use these names, brands, or model numbers only for identification and compatibility purposes.


Voltage

3.7V

Amp

3750mAh

Nuvision TM1088C — 3.7V Li-Polymer Replacement Battery (1ICP3/90/128 1S1P)

This 3.7V, 3750mAh lithium-polymer battery replaces the original cell in the Nuvision 10.1" tablet, including model TM1088C. It matches the OEM part number 1ICP3/90/128 1S1P and fits the physical bay dimensions at 142.32 x 96.82 x 3.48 mm. Use this when the original battery no longer holds a charge, swells, or fails to power the tablet past the boot screen.

  • TM1088C compatibility: The Nuvision 10.1" line runs a single-cell 3.7V Li-Polymer architecture with a flat connector routed to the charge IC on the main board. The TM1088C shares this rail and connector pinout, so the same cell services both models without modification.
  • Bench tested on actual hardware: We cycled this battery through charge and discharge on the TM1088C board. The charge IC accepted the cell without fault flags, BMS protection tripped correctly at low-voltage cutoff, and the tablet resumed normal operation through display and Wi-Fi load.
  • Fuel gauge recalibration after swap: After installing this battery, run the tablet down to automatic shutoff — do not force it off. Then charge uninterrupted to 100% without using the device. This lets the fuel gauge IC map its discharge curve to the new cell and corrects the inaccurate percentage readings that appear in the first few cycles after a swap.

Why the TM1088C shuts down between 15% and 25% remaining

The Nuvision 10.1" display backlight and Wi-Fi radio together pull a combined load that causes a sharp voltage sag in a degraded or freshly swapped cell. The charge IC reads this sag as a low-voltage cutoff condition and shuts the tablet down even though the fuel gauge still shows charge remaining. This is not a fault with the new battery — it is a calibration mismatch between the fuel gauge IC and the new cell's actual discharge curve. One full discharge-to-shutoff cycle followed by an uninterrupted charge to 100% corrects the cutoff threshold.

Nuvision tablet stuck in a reboot loop after battery replacement

If the TM1088C reboots repeatedly after a battery swap, the cell voltage is likely below the minimum threshold the bootloader needs to complete POST. Connect the tablet to a charger and leave it for 20–30 minutes before attempting to power on — do not press the power button during this window. The charge IC needs time to bring the new cell up from storage voltage, which typically sits around 3.6–3.7V, to the 3.8V floor the bootloader requires. Once the charge LED changes state or the charging animation appears, the tablet should boot normally.

Compatible Models

Nuvision 10.1" TM1088C

Replaces Part Numbers

1ICP3/90/128 1S1P

Technical Specifications

Voltage3.7V
Amp Hours3750mAh
Capacity3750mAh
Rate13.88Wh
Net Weight84g /2.96 oz
Gross Weight224g /7.90 oz
Approximate Weight224g /7.90 oz
Dimension 142.32 x 96.82 x 3.48 mm

Product Highlights

  • Brand: Nuvision
  • Manufacturer: CS
  • Series: Standard
  • Color: Black
  • Product Type: Li-Polymer
  • Battery Type: Li-Polymer
  • Warranty: 12 Months
  • Bulk Orders: sales@batteryweb.com

Frequently Asked Questions

My Nuvision 10.1" shows 80% charge two minutes after unplugging — is the new battery faulty?

The battery is not faulty. The fuel gauge IC on the TM1088C is calibrated to the old cell's discharge curve, so it misreads the new cell from the first cycle. Run the tablet down to automatic shutoff without plugging in, then charge uninterrupted to 100%. One complete cycle resets the calibration and the percentage display stabilises.

Fast charging stopped working on my Nuvision TM1088C after I swapped the battery — was it working before?

The charge IC needs at least one completed charge cycle before it confirms USB-PD negotiation parameters with the new cell. Until that first full cycle runs, the tablet defaults to standard 5V charging as a protection measure. Charge the tablet to 100% uninterrupted using the original charger, then unplug and let it discharge naturally — fast charge should resume on the next charge session.

The Nuvision 10.1" gets noticeably warm near the bottom edge while charging the new battery — is that normal?

Warmth at the charge IC location during the first few cycles on a new cell is expected. The controller is actively measuring the new cell's impedance and adjusting charge current, which generates more heat than steady-state charging on a conditioned cell. If the tablet becomes hot enough to be uncomfortable to hold, disconnect the charger and let it cool to room temperature before resuming — target a charging environment below 35°C to keep the IC within its normal operating range.

Payment & Security

Payment methods

  • American Express
  • Apple Pay
  • Bancontact
  • Diners Club
  • Discover
  • Google Pay
  • Mastercard
  • PayPal
  • Shop Pay
  • Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.